PCB Heaven

General Category => Maths, Geometry, Physics and others => Topic started by: kourt on November 27, 2009, 10:57:27 AM

Title: Firmware problem
Post by: kourt on November 27, 2009, 10:57:27 AM
Hallo. :)
I have a problem with a touch panel and if someone knows something i'll aprreciate it.
As i told you i have a touch panel BEIJER E-615.The firmware of this panel is 6.03.When i try to upload a programm in this panel , e-designer ( the programming software ) ask me for a new firmware 6.10 Version.My question is how can i convert the old version to the new ? (I hope you understood my description of my problem  :)  )Thanks
Title: Re: Firmware problem
Post by: kam on November 28, 2009, 08:15:58 AM
I do not think you can 'convert'. Instead, you need to 'upload' the new firmware. Do you have it? Or better, do you have access to a source that supplies this new firmware?


In any case, i would rather downgrade the e-designer (use an older version for example) rather than upgrading the firmware.
Title: Re: Firmware problem
Post by: kourt on November 28, 2009, 09:22:37 AM
Yes you are right , i must upload the new firmware.I found one site e-terminals.com but i don't know how to make the upload.
Also i have already check to upgrade an old version of e-designer but i stll have the same problem.KAM HELP ;) ;)
Title: Re: Firmware problem
Post by: kam on November 29, 2009, 12:27:34 PM
Send details of the screen and spic0m will find yout eh proper wire for uploading firmware.
Title: Re: Firmware problem
Post by: spic0m on November 29, 2009, 13:42:04 PM
Huh? I can't understand the problem. You have the firmware but no means (cables) to upload it? You don't have the firmware? You upload the firmware but it is not accepted?
Be more specific please.
Title: Re: Firmware problem
Post by: kourt on November 29, 2009, 21:04:00 PM
Spicommmm
loook
I have a touch panel Mitsubhi, beijer E-615 Landscape.
This panel has  firmware  V6.02c.
I can not communicate with the panel because the firmware of the software that i use is V6.10,
so i must upgrade the firmware of the panel.
I found an older version of the software  ( E-designer is the software )
i installed it but i had the same problem.
I found this link http://www.meau.com (http://www.meau.com)   but.......
 So what you think?
Title: Re: Firmware problem
Post by: spic0m on November 29, 2009, 21:10:14 PM
Sorry but i still can't understand. You want new firmaware for the screen but you installed older software?
The link wasn't much helpfull to your problem.
And i ask again: You have the new firmware for the screen?
If you have it, can you upload it?
Title: Re: Firmware problem
Post by: kourt on November 29, 2009, 21:13:14 PM
 I don't have it.
This is my problem.
Title: Re: Firmware problem
Post by: spic0m on November 29, 2009, 21:16:29 PM
Good, so you need the new firmware for the screen, ver 6.10 if i'm correct?
And how you plan to upload it?
Title: Re: Firmware problem
Post by: kourt on November 29, 2009, 21:21:15 PM
That's right.
I suppose that i will connect direct the panel with the pc with rs-232 and i do the uploading
Title: Re: Firmware problem
Post by: spic0m on November 29, 2009, 22:03:52 PM
I think you refer to the MELSEC MAC E615 panel
Title: Re: Firmware problem
Post by: kourt on November 29, 2009, 22:50:22 PM
That's right. ;)
Title: Re: Firmware problem
Post by: spic0m on November 29, 2009, 23:16:02 PM
Hmmm, i think you have a problem here. Those things cannot update the firmware. Give me a day or so to check it out.
Title: Re: Firmware problem
Post by: kourt on November 29, 2009, 23:17:39 PM
Thanks  ;)
I hope the best
Title: Re: Firmware problem
Post by: kam on November 30, 2009, 21:56:26 PM
Spic0m AKA "Der Suchemeister"  ;D
Title: Re: Firmware problem
Post by: kourt on December 01, 2009, 10:13:31 AM
Spicoogle ;D
Title: Re: Firmware problem
Post by: spic0m on December 01, 2009, 19:10:38 PM
It doesn't seem to exist any kind of firmware for that thing, the problem is that Beijer produces the screens which Melscec buys and embodies them to their product that is sold under Mitsubishi licence! If you're in a hurry check with local representative else give me a couple of days to give another check. :(